Home › Everything we make › Skirting, Architrave & Mouldings › Stirling
Stirling · Scotland
Skirting, Architrave & Mouldings in Stirling
Profiles matched to the originals and run to length, mitres cut on site.
- Free measured survey
- Fixed written quote
- Workshop-made, site-fitted
- 10-year workmanship guarantee
- Fully insured
Stirling is a county of sandstone villas, conservation-area town houses and rural farmhouses. That is exactly the kind of building stock a set of mouldings has to be drawn around, so we allow for it at survey stage rather than on fitting day — walls get checked for wind and plumb, floors for level, and the setting-out is taken from the worst reading, not the best.
How we approach it
We build skirting, architrave & mouldings as cabinetmakers rather than fitters: machined joints, real carcass construction, and a finish applied under workshop conditions before anything reaches your Stirling address.
How we build it
Timber is chosen for the room it is going into. Painted work is built in tulipwood and moisture-resistant MDF because they hold a crisp arris and take a sprayed finish without grain rise. Where the grain is meant to be seen we use European oak, walnut or ash, with veneers laid so the figure runs continuously across a set of doors.
Finish and materials
Every finished job gets a short handover: what the surface is, how to clean it, and how to adjust a hinge if a door drops after the heating has been on for a season. Adjustment is normal in timber and takes about two minutes once you know which screw to turn.
| Guide price | from £140 per linear metre, fitted |
|---|---|
| Lead time | 2–4 weeks from signed drawings |
| Construction | Primed softwood or MDF |
| Survey area | All of Stirling, including Stirling, Dunblane, Callander, Bridge of Allan |
Want a number now? The indicative price tool gives a range in about a minute. A free survey in Stirling turns it into a fixed written quote.
Towns we cover
Other joinery for Stirling
What happens next
Four steps, no surprises
Survey
A joiner visits, measures the opening, checks for level and plumb, and talks through how you want to use the space.
Drawings & quote
You get a setting-out drawing and a fixed written price. Nothing is ordered until you have approved both.
Workshop
Parts are machined, assembled and finished under cover while the site carries on with other trades.
Fit & handover
We fit, scribe, adjust and touch in, then walk you through care and adjustment before we leave.
Straight answers
Skirting, Architrave & Mouldings in Stirling — common questions
Can you supply long lengths without joints?
Up to 4.2m in MDF and around 3m in solid timber as standard. Beyond that we scarf-joint rather than butt, so the joint closes invisibly under paint.
What height should skirting be?
It should relate to the ceiling. In a 2.4m room, 145mm to 170mm looks right. In a 3m Victorian room, 220mm and above. Skirting that is too short is the commonest mistake in a period refurbishment.
Do you fit or supply only?
Either. Supply-only is straightforward for a competent joiner or a confident DIYer. We fit where the mitres are complex, the walls are out, or the profile is large enough that a bad joint would show.
Can you run picture rails and coving too?
Timber and MDF picture rails and dado rails, yes. Plaster coving and cornice is a plasterer's trade and we work alongside them rather than supplying it.
Can you match existing joinery in the house?
Yes. We take a profile of the existing skirting, architrave or door and either match it from stock cutters or have a cutter ground so the new work runs identically. Matching an old paint colour is straightforward; matching aged oak takes a sample panel and a couple of attempts, which we build into the programme.
Start with a measurement
Tell us the space in Stirling — we’ll tell you what it costs
Every quote starts with a free measured survey, so the price you get is the price you pay. No deposit is taken until you have drawings you are happy with.