Home › Everything we make › Skirting, Architrave & Mouldings › Wrexham
Wrexham · Wales
Skirting, Architrave & Mouldings in Wrexham
Profiles matched to the originals and run to length, mitres cut on site.
- Free measured survey
- Fixed written quote
- Workshop-made, site-fitted
- 10-year workmanship guarantee
- Fully insured
Wrexham is a county of brick terraces, former colliery housing and expanding modern estates. That is exactly the kind of building stock a set of mouldings has to be drawn around, so we allow for it at survey stage rather than on fitting day — walls get checked for wind and plumb, floors for level, and the setting-out is taken from the worst reading, not the best.
How we approach it
Every set of mouldings we make starts with a site survey and a set of setting-out drawings, not a catalogue page. We measure the opening in Wrexham, check the walls for wind and the floor for fall, then cut a carcass that fits the room you actually have.
How we build it
Hardware is specified to the weight it is carrying, not to a price point. Soft-close runners are rated for the drawer load, hinges are adjustable in three planes, and sliding gear is sized so a full-height door still moves with one finger a decade later.
Finish and materials
Every finished job gets a short handover: what the surface is, how to clean it, and how to adjust a hinge if a door drops after the heating has been on for a season. Adjustment is normal in timber and takes about two minutes once you know which screw to turn.
| Guide price | from £140 per linear metre, fitted |
|---|---|
| Lead time | 2–4 weeks from signed drawings |
| Construction | Primed softwood or MDF |
| Survey area | All of Wrexham, including Wrexham, Ruabon, Chirk, Rhosllanerchrugog |
Want a number now? The indicative price tool gives a range in about a minute. A free survey in Wrexham turns it into a fixed written quote.
Towns we cover
Other joinery for Wrexham
What happens next
Four steps, no surprises
Survey
A joiner visits, measures the opening, checks for level and plumb, and talks through how you want to use the space.
Drawings & quote
You get a setting-out drawing and a fixed written price. Nothing is ordered until you have approved both.
Workshop
Parts are machined, assembled and finished under cover while the site carries on with other trades.
Fit & handover
We fit, scribe, adjust and touch in, then walk you through care and adjustment before we leave.
Straight answers
Skirting, Architrave & Mouldings in Wrexham — common questions
Can you match a Victorian skirting profile?
Yes. We take a profile gauge from a clean section, have a cutter ground if it is not in our stock range, and run it in whatever length you need. Ogee, torus and lambs tongue are all held as standard.
MDF or timber?
Primed MR MDF for painted skirting and architrave — it is straighter, cheaper and takes paint better. Solid timber only where it will be stained or where the profile is deep enough to need the strength.
How do you deal with uneven walls?
Scribe the back of the board to the wall rather than filling the front. Filler along a top edge cracks within a heating season; a scribed board does not.
What is the right architrave to skirting relationship?
Architrave is normally a little narrower than the skirting is tall, and the skirting dies into a plinth block at the base of the architrave in a traditional setting. It solves the awkward junction where a deep skirting meets a shallower architrave.
Do I need to empty the room before you fit?
Clear the working wall and anything fragile. We bring dust sheets and a vacuum-extracted saw, but fitting makes dust and we would rather your furniture was out of the way. For kitchens we will agree a sequence with you so you keep a sink and a kettle for as long as possible.
Start with a measurement
Tell us the space in Wrexham — we’ll tell you what it costs
Every quote starts with a free measured survey, so the price you get is the price you pay. No deposit is taken until you have drawings you are happy with.