Home › Everything we make › Wall Panelling & Wainscoting › Herefordshire
Herefordshire · Midlands
Wall Panelling & Wainscoting in Herefordshire
Shaker, board-and-batten or raised panel, set out to the room's real lines.
- Free measured survey
- Fixed written quote
- Workshop-made, site-fitted
- 10-year workmanship guarantee
- Fully insured
Herefordshire is a county of half-timbered farmhouses, sandstone cottages and low-density rural properties. That is exactly the kind of building stock a run of wall panelling has to be drawn around, so we allow for it at survey stage rather than on fitting day — walls get checked for wind and plumb, floors for level, and the setting-out is taken from the worst reading, not the best.
How we approach it
We build wall panelling & wainscoting as cabinetmakers rather than fitters: machined joints, real carcass construction, and a finish applied under workshop conditions before anything reaches your Herefordshire address.
How we build it
Timber is chosen for the room it is going into. Painted work is built in tulipwood and moisture-resistant MDF because they hold a crisp arris and take a sprayed finish without grain rise. Where the grain is meant to be seen we use European oak, walnut or ash, with veneers laid so the figure runs continuously across a set of doors.
Finish and materials
Finishing happens in the workshop wherever possible. Sprayed paint gives an even film that brushwork cannot match, and the only work left on site is the final touch-in around scribes and fixings.
| Guide price | from £320 per linear metre, fitted |
|---|---|
| Lead time | 3–4 weeks from signed drawings |
| Construction | MR MDF, hand-painted |
| Survey area | All of Herefordshire, including Hereford, Leominster, Ross-on-Wye, Ledbury |
Want a number now? The indicative price tool gives a range in about a minute. A free survey in Herefordshire turns it into a fixed written quote.
Towns we cover
Other joinery for Herefordshire
What happens next
Four steps, no surprises
Survey
A joiner visits, measures the opening, checks for level and plumb, and talks through how you want to use the space.
Drawings & quote
You get a setting-out drawing and a fixed written price. Nothing is ordered until you have approved both.
Workshop
Parts are machined, assembled and finished under cover while the site carries on with other trades.
Fit & handover
We fit, scribe, adjust and touch in, then walk you through care and adjustment before we leave.
Straight answers
Wall Panelling & Wainscoting in Herefordshire — common questions
Can panelling go over a chimney breast or around a radiator?
Yes. Setting out is the whole job here — the panel widths are calculated so the divisions land sensibly either side of features rather than a half panel appearing at a corner.
Does it need to be painted on site?
Panelling is usually installed primed and painted in place, because the fixing and filling has to happen first. We can supply it sprayed if a decorator is doing a cut-in only.
Can sockets and switches stay where they are?
They need extending forward by the panel thickness with a spacer collar — a small electrical job. We mark the positions and cut the apertures to suit.
How high should panelling go?
Dado height at roughly one third of the wall — usually 900mm to 1,100mm — for a traditional room. Full height for drama in a hallway or behind a bed. Two thirds height reads awkward and is worth avoiding.
Is bespoke joinery more expensive than a fitted furniture chain?
On a like-for-like specification it is usually comparable, and often less. Chains price a standard carcass and then charge for every deviation. A bespoke maker prices the actual room once. Where bespoke does cost more is in the materials — solid hardwood and sprayed finishes cost more than foil-wrapped board, and they last a great deal longer.
Start with a measurement
Tell us the space in Herefordshire — we’ll tell you what it costs
Every quote starts with a free measured survey, so the price you get is the price you pay. No deposit is taken until you have drawings you are happy with.