Home › Everything we make › Wall Panelling & Wainscoting › Northumberland
Northumberland · North East
Wall Panelling & Wainscoting in Northumberland
Shaker, board-and-batten or raised panel, set out to the room's real lines.
- Free measured survey
- Fixed written quote
- Workshop-made, site-fitted
- 10-year workmanship guarantee
- Fully insured
Northumberland is a county of thick-walled stone cottages, estate housing and remote rural properties. That is exactly the kind of building stock a run of wall panelling has to be drawn around, so we allow for it at survey stage rather than on fitting day — walls get checked for wind and plumb, floors for level, and the setting-out is taken from the worst reading, not the best.
How we approach it
Every run of wall panelling we make starts with a site survey and a set of setting-out drawings, not a catalogue page. We measure the opening in Northumberland, check the walls for wind and the floor for fall, then cut a carcass that fits the room you actually have.
How we build it
Carcass work is birch ply or MR MDF depending on span and load. Face frames and doors are solid hardwood. Everything is machined on the same setting so stiles, rails and reveals line through, and shadow gaps stay parallel from one end of the run to the other.
Finish and materials
Every finished job gets a short handover: what the surface is, how to clean it, and how to adjust a hinge if a door drops after the heating has been on for a season. Adjustment is normal in timber and takes about two minutes once you know which screw to turn.
| Guide price | from £320 per linear metre, fitted |
|---|---|
| Lead time | 3–4 weeks from signed drawings |
| Construction | MR MDF, hand-painted |
| Survey area | All of Northumberland, including Morpeth, Alnwick, Hexham, Berwick-upon-Tweed |
Want a number now? The indicative price tool gives a range in about a minute. A free survey in Northumberland turns it into a fixed written quote.
Towns we cover
Other joinery for Northumberland
What happens next
Four steps, no surprises
Survey
A joiner visits, measures the opening, checks for level and plumb, and talks through how you want to use the space.
Drawings & quote
You get a setting-out drawing and a fixed written price. Nothing is ordered until you have approved both.
Workshop
Parts are machined, assembled and finished under cover while the site carries on with other trades.
Fit & handover
We fit, scribe, adjust and touch in, then walk you through care and adjustment before we leave.
Straight answers
Wall Panelling & Wainscoting in Northumberland — common questions
Can sockets and switches stay where they are?
They need extending forward by the panel thickness with a spacer collar — a small electrical job. We mark the positions and cut the apertures to suit.
How high should panelling go?
Dado height at roughly one third of the wall — usually 900mm to 1,100mm — for a traditional room. Full height for drama in a hallway or behind a bed. Two thirds height reads awkward and is worth avoiding.
Can panelling go over a chimney breast or around a radiator?
Yes. Setting out is the whole job here — the panel widths are calculated so the divisions land sensibly either side of features rather than a half panel appearing at a corner.
Does it need to be painted on site?
Panelling is usually installed primed and painted in place, because the fixing and filling has to happen first. We can supply it sprayed if a decorator is doing a cut-in only.
Can you match existing joinery in the house?
Yes. We take a profile of the existing skirting, architrave or door and either match it from stock cutters or have a cutter ground so the new work runs identically. Matching an old paint colour is straightforward; matching aged oak takes a sample panel and a couple of attempts, which we build into the programme.
Start with a measurement
Tell us the space in Northumberland — we’ll tell you what it costs
Every quote starts with a free measured survey, so the price you get is the price you pay. No deposit is taken until you have drawings you are happy with.